Researchers at the University of Toronto went through the water supply timetables published by Delhi and Bengaluru and found 3,278 different schedules. At one end, some households get water almost all day. At the other end, some get about 30 minutes a week.
Same city, same water board, sometimes only a few streets apart. The difference is not decided at the dam or at the treatment plant. It is decided somewhere in the middle, and that middle is the part most explainers skip. They draw a dam, a plant and a tap, and stop there.
This article follows the water in the order it actually travels, from the source to your overhead tank, and then spends real time on the question people ask while standing next to an empty tap: why does it come for only a few hours? The figures come from government manuals, a Parliament committee report from December 2025, official survey data and a few academic studies. Where a number is old, the text says so. Everything was checked against the sources listed at the end on 21 November 2026.
The eight stops, in one look
Every city does it a little differently, but the chain is the same.

- Source: a river, dam, canal or a field of borewells.
- Raw-water pumping: canals and pipelines that bring untreated water to the city.
- Treatment plant: where the water is cleaned and disinfected.
- Clear-water reservoir: treated water waits here and is pumped out.
- Service reservoirs: tanks spread across the city, elevated or at ground level.
- Zones and valves: the city is cut into areas, and valves decide which area gets water and when.
- Street main and service pipe: the last stretch of pipe, usually with a meter.
- Your own sump, pump and overhead tank.
Stop 6 is the one that decides when your tap runs. It is also the stop almost nobody writes about, so much of this article is about stops 5 to 8.
Stops 1 and 2: where the water comes from, and how far it travels
Most big cities do not sit next to the water they drink. The housing ministry’s revised water manual of 2024 says that as local sources run dry or get polluted, cities are being pushed towards distant ones, and moving water over long distances is expensive.
Delhi shows how far this can go. An ORF analysis of the city’s sources says that more than 90 per cent of its water is surface water that comes from Haryana, Uttar Pradesh and Himachal Pradesh. It arrives through canals. The Western Yamuna and Munak canals carry Yamuna and Bhakra water through Haryana, and the Upper Ganga Canal brings Ganga water from Uttar Pradesh. The Yamuna itself is about 1,376 km long, and only about 52 km of that lies inside Delhi. Even with all this, the Delhi government told the Rajya Sabha in July 2024 that supply falls short of the per-person norm by about 160 million gallons a day.
Bengaluru’s problem is height as much as distance. The city sits far above the Cauvery, which is about 100 km away, so the water has to be pumped uphill. For Cauvery Stage V, inaugurated in October 2024, the water board built three booster pumping stations, at Thorekadanahalli, Harohalli and Tataguni. Together they push 775 million litres a day through roughly 110 km of steel pipe and several hundred metres of climb, according to the Deccan Herald’s report on the launch.
Cities also lean on borewells, and moving away from them is slow work. Under the first phase of AMRUT, 490 projects shifted a town’s supply from groundwater to surface water, drawing over 6,700 million litres a day, the housing ministry told the Parliament committee.
Who runs all this? Water is a state subject, and since the 74th Constitutional Amendment of 1992, urban water supply is legally the job of city governments. In practice the work is split between municipalities, state water boards and public health engineering departments. The 2024 manual calls this arrangement fragmented. The Parliament committee noted in December 2025 that in practice state-run parastatal agencies still dominate the planning and building, and city governments have often had little say.
Stop 3: the treatment plant, and the standard it has to meet
Raw water from a river or canal is muddy and carries germs, and sometimes chemicals. A treatment plant cleans it in a fixed order. Floating junk is screened out first. A coagulant, usually alum, is added so that fine dirt clumps together. The clumps settle in large tanks. Sand filters catch what stays behind. Last comes chlorine, which kills germs and leaves a small amount behind to protect the water on its way through the pipes. Bigger plants add more steps, but this is the backbone.
What counts as clean enough? The reference is IS 10500:2012, the Bureau of Indian Standards specification for drinking water, as amended in 2018. Two of its numbers matter for this story.
| Parameter | Acceptable limit | Permissible where no better source exists |
|---|---|---|
| Turbidity (cloudiness) | 1 NTU | 5 NTU |
| Free residual chlorine (minimum) | 0.2 mg per litre | up to 1 mg per litre |
The standard adds that the chlorine is to be tested at the consumer’s end, and that where protection against viruses is needed the minimum should be 0.5 mg per litre. BIS has a working group reviewing the standard, so the numbers may change. The 2012 version is the one BIS lists today.
Look at that chlorine rule again. It is measured at the consumer’s end, not at the plant gate. The standard itself assumes that a clean plant is not enough, and that the water must stay clean through kilometres of pipe. That is where things tend to go wrong, and the later sections explain why.
How often does the water pass? In December 2025 the housing ministry told a Parliament committee that 99 per cent of samples passed at treatment plants and 98.82 per cent at household level, tested for E. coli, arsenic and fluoride. In the same presentation, another slide showed only 66 per cent of household samples meeting BIS standards. Asked about the gap, the ministry said the two figures were different data covering different cities. The committee put both on record.
Stops 4 to 6: reservoirs, zones and the person with the valve key
After treatment, the water collects in a clear-water reservoir at the plant. From there, pumps and large trunk mains carry it to service reservoirs spread around the city, some elevated and some at ground level. Each reservoir feeds one part of the city, and the pressure it gives depends on its height and on how much water is in it.
The 1999 manual recommended minimum pressure at the street pipe of 7 metres of water head for single-storey buildings, 12 metres for two-storey buildings and 17 metres for three-storey buildings, as the preface of the 2024 manual recalls. In plain words, the water in the main has to be pushed high enough to reach your floor. Where pressure sags, upper floors and the far ends of lines go dry first.
Between the reservoir and your street there is something no standard diagram shows: a person with a valve key. In most Indian cities water is supplied by rotation. The network is cut into supply areas, and operators called valvemen open and close valves so that one area gets water, then the next. A 2012 study in Hubballi-Dharwad found over 50 valvemen turning more than 800 valves in a single supply cycle, which is the time it takes to cover the whole city once. A 2016 GSMA report on a text-alert start-up that worked with Bengaluru’s water board put the number of hand-operated valves in that city at around 8,000, and said valvemen could not always keep to their assigned schedule. In a household survey in Bengaluru in 2014-15, researchers found that the published schedule was generally inaccurate in their study area.
Which means the timing of your water is a decision made at the zone level, by people and valves, long before the water reaches your tap. It is not a property of your tap, your building or even your locality alone.
Stops 7 and 8: from the street main to your sump
From the street main, a thinner service pipe runs to the property, usually through a meter, and ends in an underground sump. Most Indian houses are built around this. Down To Earth described the sump in 2012 as standard in house design, with those who can afford it pumping water up to an overhead tank and the rest lifting it in buckets. Some households go further. The same report describes taps fitted below the level of the feeder line, and electric pumps that draw water straight from the main, which it calls illegal.
The sump is not only a household matter. The preface of the 2024 manual lists preventing contamination between the distribution system and household underground sumps as a vital challenge. So the chain does not end at your gate. It ends in your tank.
So why does the tap run for only a few hours?
It is the rule, not the exception
The 2024 manual’s preface states that in almost all towns, water supply is intermittent, lasting 2 to 6 hours a day. A benchmarking pilot by the urban ministry in 28 cities in 2009 found an average of 4.7 hours a day against a goal of 24. The Parliament committee’s 2025 report quotes an expert committee figure of 1 to 6 hours. Three documents, up to fifteen years apart, and the same range.
It is not only a shortage
Cities do lose water on the way, but raw quantity alone does not explain the short hours. In 2025 the ministry reported an average urban supply of 122 litres per person per day against a benchmark of 135. That number rests on what cities report, in a country where metering is patchy: the 2009 pilot found only 34.6 per cent of connections metered. A CAG performance audit of Hyderabad’s water board found that the net water available per person was 118 litres against 150 required, mainly because of 39 per cent losses, and that the water actually supplied ranged between 66 and 71 litres per person. Water experts have argued for years that the problem is mostly one of management, not of the amount of water in the source.
Leaks, and the pressure trade-off
A large share of the treated water never earns a rupee. The 2011 High-Powered Expert Committee report, quoted in the Parliament committee’s 2025 report, put this “non-revenue water” at about 50 per cent of production, against 5 per cent in Singapore. It also said nearly 70 per cent of leakages come from faulty household connections or malfunctioning meters. The urban ministry’s own 2009 pilot found an average of 41.8 per cent against a 15 per cent benchmark. The target under AMRUT 2.0 is below 20 per cent, and ₹400 crore is set aside as an incentive for states that reach it. By the time of the committee’s report, no state had claimed it.
Down To Earth described what utilities do about leaks: they reduce the pressure in the pipes and limit the hours of supply. Lower pressure means less water escapes through the cracks. It also means a thin trickle at the tap, for a short time.
A design problem built in
The preface of the 2024 manual also makes an admission. The 1999 manual had recommended 24×7 pressurised supply, but it left out the idea of operational zones and district metered areas (DMAs), which are small parts of the network with their own meters. So cities planned large networks, and in the manual’s words these slid back to intermittent supply soon after they were commissioned. A big network with leaks and limited water cannot keep every pipe full, so it takes turns. That is the rota from the previous section.
Why the schedules look the way they do

The Toronto study found that in Delhi, more than 60 per cent of the city gets water between 6 and 8 in the morning, and nearly 50 per cent between 6 and 8 in the evening. Outside those windows, supply is off for more than 90 per cent of the city. Bengaluru does not show the same daily peak. For most households there, water comes on alternate days or less often, sometimes at hours like 2 a.m. In both cities richer neighbourhoods have more piped connections, and in Bengaluru they also get better schedules.
What empty pipes do
The High-Powered Expert Committee report says that without continuous pressure, street run-off, drainage water, raw sewage from nearby sewer lines and leaking septic tanks can be sucked into water mains. The 2024 manual makes the same point, saying water in the pipeline gets contaminated during the hours it is not being supplied. Down To Earth added a less obvious cost: meters are built for continuous flow, and the vacuum in an emptied pipe can wreck their readings, while pipes that fill and empty every day take more shocks, the “water hammer” effect. Both feed back into the leak and billing problems above. Each problem makes the next one worse.
Has any Indian city managed 24×7?
The idea is not new. Down To Earth reported in 2012 that supply hours and pressure had dropped sharply over the previous three decades, and that a group of officials formed the Change Management Forum in 2002 to push for round-the-clock supply. It became official urban policy with the JNNURM in 2005.
The best-known early test was in Karnataka. In April 2008, 178,700 people in five demonstration zones in Belgaum, Hubli-Dharwad and Gulbarga began getting 24×7 water. In Belgaum, the same report says, 95 per cent of the pipeline network was replaced between 2005 and 2008. A Veolia manager told the magazine that in Dharwad monthly collections rose from ₹2.5 lakh to ₹8 lakh while daily water use fell from four million litres to 3.1 million. A critic, ActionAid’s Kshitij Urs, pointed out that the demonstration zones had few poor residents, so the results might not scale. In Badlapur, near Mumbai, eight of 34 wards had round-the-clock water in 2012, but leakage stayed above a third and consumption went up.
Two later examples get cited often. Malkapur in Maharashtra has had 24×7 supply since 2009. In July 2021 the Odisha government launched its Sujal “drink from tap” scheme in Puri and described it as the first Indian city with round-the-clock drinking-quality supply and fully metered household connections. Mongabay India reported that it began with about 32,000 households.
At national level the picture is less clear. AMRUT 2.0 has approved 382 projects worth ₹25,296 crore to enable 24×7 supply in at least one ward or DMA of a town. But when the Parliament committee asked the housing ministry in 2025 how many cities have 24×7 supply, the reply did not say, and the ministry’s table left that line blank. The committee recorded the same gap for non-revenue water and metering.
The 2024 manual’s answer is smaller zones, DMAs, full metering and, where it helps, private operators. Not everyone is convinced. A group of researchers argued in The Conversation in 2023 that setting a continuous-supply target for existing networks will repeat the failure of the 1999 manual. Both views are on record, and the next few years of data will show which one holds.
What the city’s rota costs inside your house
The cost of the rota does not disappear. It moves into your home. The Toronto team puts it simply: if water comes only in the morning and evening, you need storage to last the other ten hours or so, and if it comes every other day, you need more. That costs money, takes space, and gives microbes more time to grow in the tank. In Bengaluru, the study found that poorer neighbourhoods got worse schedules than richer ones, which forces those households to invest in more storage. ASCI’s V. Srinivas Chary, quoted in the Down To Earth report, listed more costs of intermittent supply: sumps, pumps, hours spent waiting for water, buying from private suppliers, and health costs.
Three things are worth doing with all this.
- Find your own zone’s timetable. Delhi and Bengaluru publish theirs online. Check your own water board’s website or ward office. Treat the timetable as a guide, since the Bengaluru survey found published schedules were often wrong.
- Treat your sump and tank as part of the water system. Keep them covered and clean them at the interval your local board recommends. The 2024 manual names household sumps as a contamination risk in its own right.
- Do not assume the water is drinkable straight from the tap. Unless your water board has formally said your area is covered by a drink-from-tap scheme, the safer assumption is that the water needs treating at home. Puri is the best-known place where such a claim has been made.
A tap connection is not the same as water from the tap
A connection and a flow of water are two different things, and India’s own data shows the gap. Administrative data from the rural tap water scheme reported that over 60 per cent of rural households had a tap connection at home by the middle of 2023. The NSS survey of 2022-23 asked households what they actually drank from for most of the year. It found that 40 per cent of rural households used piped water as their main source, and only 30 per cent had a tap in their own home or yard as the main source. These are Data For India’s figures, drawn from both sources.

The two numbers do not contradict each other. One counts connections provided, the other counts water in use. The statistics ministry says the same in its release on the survey: the survey records the source a household used most over 365 days, while the administrative record counts pipe connections.
In cities, piped water is the biggest single source, but bottled water now serves about 15 per cent of urban households, according to the same Data For India analysis. The statistics ministry also reports that 95.7 per cent of Indian households have access to an “improved” source of drinking water. That group includes tube wells, hand pumps and packaged water, so the figure says little about how many homes get water from a pipe.
The village version of this story
The chain is shorter in a village: usually a local source, a small treatment step, an overhead tank and a network of village pipes. The scale of the effort is large. When the Jal Jeevan Mission began in August 2019, 3.23 crore rural households, or 16.71 per cent, had tap connections. The Jal Shakti minister told the Lok Sabha that as of 18 July 2026, 15.89 crore of 19.36 crore rural households, or 82.09 per cent, have tap water supply in their homes. The Cabinet has extended the mission to December 2028, and the minister put the enhanced outlay at ₹8.69 lakh crore. Rural schemes under the mission are designed for 55 litres per person per day in non-desert areas, according to a CAG audit of Haryana.
The minister also cited an independent functionality assessment from 2024, in which 98.1 per cent of surveyed households had tap connections and 87 per cent said they had received water in the previous week. The NSS comparison in the section above is from 2022-23, and coverage has grown since, so a newer household survey is what will show how much of that growth reaches people as water in use. Keeping village systems running day to day is the gram panchayat’s job, and our explainer on how a gram panchayat gets its money covers that side.
Questions people ask
How does water travel from a dam or river to a house in India?
It is pumped or channelled to a treatment plant, cleaned and chlorinated, stored in a clear-water reservoir, sent through large mains to service reservoirs, and then released to neighbourhoods through valves on a rotation. From the street main, a service pipe takes it to the house, where it usually fills an underground sump before being pumped to an overhead tank.
Why does water come at a fixed time every day?
Most Indian cities supply water by rotation, with valves opened zone by zone, instead of keeping every pipe full all day. Official documents put supply at 2 to 6 hours a day in almost all towns. Leaks, limited pressure and networks that were not planned in small metered zones all push cities towards the rota.
What do MLD and LPCD mean?
MLD is million litres per day, the volume a plant or a city handles. LPCD is litres per capita per day, the amount supplied for each person. The 1999 CPHEEO manual set 135 LPCD for cities with sewerage, 150 for metropolitan and mega cities, and 70 for towns that have piped water but no sewerage. Rural schemes under the Jal Jeevan Mission use 55 LPCD.
What is non-revenue water?
It is water that a utility treats and pumps but never bills for, because of leaks, theft, or missing and faulty meters. The urban ministry’s 2009 pilot across 28 cities found an average of 41.8 per cent against a benchmark of 15 per cent. AMRUT 2.0 aims to bring it below 20 per cent.
Is tap water safe to drink in India?
It depends on the city, the zone and the pipes. The legal reference is IS 10500:2012, and the Parliament committee was given conflicting sample results in 2025. Official documents say water in intermittent systems can be contaminated while the pipes are empty. Unless your water board has formally declared your area drink-from-tap, treating the water at home is the safer choice. If you are unsure, ask your local water board for its latest test reports.
Sources
- MoHUA / CPHEEO, Manual on Water Supply and Treatment Systems (Drink from Tap), Part C: Management, March 2024 (preface and chapter 1).
- Standing Committee on Housing and Urban Affairs, Seventh Report (18th Lok Sabha): Review of AMRUT with special emphasis on Urban Drinking Water, December 2025.
- MoHUA, Urban water supply and sanitation note, with the 2009 service level benchmark pilot results.
- Bureau of Indian Standards, IS 10500:2012, Drinking Water Specification, with Amendment No. 2 (2018); BIS working group page.
- University of Toronto Civil and Mineral Engineering, Why do Delhi and Bengaluru supply water according to 3,278 different schedules?, June 2023 (study by David Meyer and team, published in Science of the Total Environment).
- ORF, Tracking water sources for Delhi.
- Rajya Sabha, Question 265, 29 July 2024.
- Deccan Herald, Cauvery Stage V project to be launched on Vijayadashami; Citizen Matters, Promise of Cauvery Stage V.
- USENIX NSDR 2012, paper on intermittent supply and valve operators in Hubli-Dharwad; GSMA, NextDrop: Water Simplified, 2016; Springer, Engineering predictable water supply: the humans behind the tech.
- Down To Earth, Divining round the clock water, July 2012.
- CAG, Performance audit of water supply in the Hyderabad agglomeration.
- Data For India, Access to drinking water; MoSPI via PIB, Results of the Comprehensive Annual Modular Survey 2022-23.
- The Tribune / ANI, Rural tap water coverage has crossed 82%, July 2026; Cabinet decision on extension of the Jal Jeevan Mission; CAG, audit on rural and urban water supply in Haryana.
- ThePrint, Drinkable tap water, 24×7; Odisha TV, Sujal Mission: Puri; Mongabay India, Clean tap water mission in Puri.
- The Conversation, India’s new manual for water supply will replicate past failures, December 2023.

Hi, I’m Aryan, the writer behind IndiaClarity. I write plain-language explainers on how India’s systems, places and history work. Before I publish, I check facts against primary sources such as official records, Parliament answers, Census data and Acts of law, and I list the sources at the end of each article. If you spot a mistake, write to me at 7brewusaofficial@gmail.com and I will fix it.